Showing posts with label dumpster diving. Show all posts
Showing posts with label dumpster diving. Show all posts

7/5/08

Project Mickstee: Episode III: Deep Clean

Rubbing of all the rust, dirt and grease was definitely the longest part. Bearings, races, cups and cones were soaked overnight in the MEC degreaser, which is very pleasant to work with - it cleans well, even old grease, has virtually no smell and is biodegradable. The toothbrush in the picture (big mystery why it was in my room in the first place!) turned out to be a very handy tool to clean inside the bearing retainers and the headset crowns (since I never managed to take it apart completely).

As for the rust, a bunch of things were discovered:

1. Steel wool works best to remove rust from irregularly shaped surfaces with sharp edges (chainring).
2. Sandpaper works best on harder parts (locknuts, washers, etc), if you are crazy enough to reuse them. Not like there is anything wrong with it, but it takes bloody long time to get them to the appropriate state!
3. To remove rust from flat or just large-surfaced chromed areas, the best way was crumbled aluminum foil soaked in Coca Cola (go, H3PO4, go!). The parts end up being more shiny than after the steel wool or sandpaper. The downside - they also end up sticky, so have to be washed with water and dried.

However, the most efficient use of Coca Cola is by far the cleaning of spokes: don't even need to rub them much! Out of sheer curiosity (by this point I already bought new spokes), I made a "tub" out of aluminum foil , put three most rusted spokes and nipples in it, and marinated them in Coke for 24 hours. The result exceeded all expectations! Spokes became smooth and completely rust free, including the threading; nipples ended up as shiny as new ones. All I had to do is wipe and rinse them.

The algorithm for particularly stubborn rust (e.g. inside the rims) was something like foil+Coke -> dry excess -> wool -> more Coke -> wash and dry. Repeat as many times as needed (some parts took 4-5 runs!)

6/28/08

Project Mickstee: Episode II: Deconstruction

I managed to dismantle the bicycle down to the frameset. The stem was (and still is) dead stuck inside the steerer, and I didn't want to resolve to heat; inspection of cups and bearings showed them being in excellent condition, so I removed old grease with an oil-remover soaked toothbrush and re-greased the bearings. I know it's cheating, but the idea of this project is to keep as many original parts as possible and not to spend a fortune. Plus the fork has pretty cool lugs, and is in too good condition to replace just yet.

Taking the bike apart showed that it has not been ridden much in the last... mmm... lets say 5 years. The rust was mostly on the top left side, almost none on the frame (95% on the chrome parts). It looked like there was constant source of dampness on one side, while the other remained relatively protected. The frame is not scratched either; all cups and bearings are in perfect condition.

Moreover there is epic spiderweb inside the fenders and brake handles: I dropped a washer in it by accident, and it got stuck there!


The lady is taking her bath; the frame is metallic brown, so it camouflages rust perfectly (good to hide a half-ass derusting job, bad because it makes the rust easy to miss: the cause of the half-ass job!). Washing it removed about half of the stuff that looked like rust at first, but turned out to be dirt. Also showed the almost new condition of the frame. Serious rust was only inside the fenders.

The wheels are entirely different story. Steel rims ("heavy as a prerevolutionary iron"), gathered some rust, but still look pretty cool, and make me want to reuse them to keep the original parts on. Hubs are in average condition. Spokes, on the other hand, loosened and rusted, so at least the back wheel is to rebuild. Now, the Great Wheel Dilemma arises: to use the heavy and rust prone steel rims, or to upgrade to aluminum. If to upgrade, then it would make sense to upgrade the hubs as well. The second part of the dilemma is to whether keep it as a 5-speed (reuse same rear hub and/or sprockets) or to put a coaster brake. Coaster brake solves the potential problem with rusty brake levers and handles, and derailer. This also makes the bike lighter, and can compensate for the use of steel rims, and reduces the problems with wet weather braking.

6/24/08

Project Mickstee: Episode I: Road Find

On the day of the Saint Jean Baptiste anno domini 2008, a bicycle and a half was found in the trash pile in front of Mahatma Ghandi park. The half was nothing special - a cheap mountain bike frame with some rust, with no brakes and one wheel. But the bicycle... the bicycle didn't look like much either - rust, bolts missing on the front axle so the wheel is falling out, useless chain... Looking closer: a mixte frame '70s C.C.M. 5 speed cruiser. Cruiser handlebars. No structural damage to the frame. Appears to have all (or most) original components. Leather spring-loaded seat. Beautiful even in its rustiness.

Bringing it home, I feel like an animal rescuer from a child story. My room already looks like a bike shop - two frames from the ongoing projects, the mountain bike frame I piked up today, and a bike waiting to be tuned up and sold; plus the one I ride on daily bases. This dysfunctional family welcomes the newcomer by falling over and the symphony of clinngggs and bannngs.


Handlebars seem to have taken most of the damage from rust. Even the chain is in better condition (but still unusable). Hopefully they are still salvageable; we'll see what does the steel wool have to say on the subject.











The progress of the work will be reflected in regular reports. Stay tuned.